It looks like underextrusion at speed. It might be a clog or you might want to try a higher hotend temperature. PLA can have inconsistent ideal temperatures even with the same brand due to different colors and additives between batches and 185 is on the low side.

Right image, but under those each one below would also be wearing large pants covering each side of the subtree.

It’s not well explained for sure but judging by the names of the cookies I bet those store the consent (opt in/out) values for the other tracking options. Another way of putting it would be those are functional cookies related to the cookie consent form itself so that you don’t have to re-select consent options every time you visit the site.

If 35° (or something close to it) is the slicer setting for overhang detection it likely changes the cooling/speed/flow settings. If that is the case you can set it to a lower detection value and maybe get better results or change the normal cooling/speed/flow to be closer so it isn’t as drastic of a change.

From what I’ve read is not authentication bypass, it’s a RCE using certificates to deliver the payload. If a specific signature is found it runs the code that was sent in place of the signing public key. It also means that only someone who has the ability to generate that specific key signature could use the RCE.

There were some other bits that looked like they could have been placed to enable compromising other build systems in the future when they checked for xz support.

If filesystem UUIDs are IP equivalents. Then device paths are MAC addresses. FS labels are DNS. Device mapper entries are service discovery.

The biggest issue is that your corners are lifting from the bed during the print. Fixing this is usually a combination of making sure the bed is clean and adding a brim to increase adhesion. Maybe messing with temperature and cooling fan settings for the first few layers.

Second is things look a bit over extruded. This could just be due to the corner issue though so fix that before any other changes.

The reasoning is that it is not illegal to fake most student ID cards but it is a federal offense to fake or alter government issued ID documents.

That way if it becomes an issue they can just pass it on to the authorities as their problem.

“Invalid” or “unparseable” are more understandable descriptors in normal language. I don’t think I ever heard of garbage/junk being used for that in language theory but it may be domain specific usage.

As someone who also has produced code that looks like random characters spewed onto a terminal while using fpdf, I feel this one.

It can still have issues with potential attacks that would redirect your client to a system outside of the VPN. It would prevent MitM but not complete replacement.

IIRC the PS3 had it’s firmware encryption key published not the source code.

There is also SMS passive reading using LEO intercept. Hacked police email accounts are used to gain access to carrier systems where they use “imminent threat” no warrant lookups to pull the SMS in real time.

SMS is a terrible form of 2FA, better than none but not by much.

Your experience may depend on which distro you use and how you install things. If you use a distro with a stable upgrade path such as Debian and stick to system packages there should be almost no issues with upgrades. If you use external installers or install from source you may experience issues depending on how the installer works.

For anything complex these days I’d recommend going with containers that way the application and the OS can be upgraded independently. It also makes producing a working copy of your production system for testing a trivial task.

Fridges with a dial usually are an uncalibrated simple analog thermostat sensor (often a gas tube with a pressure switch) along with a simple analog control board. Fridges with a digital thermostat tend to use a calibrated sensor (usually a thermocouple) with a digital control board.

You might also try running a few leveling probes in a row to check the repeatability of the measurements. It’s possible that something is messing with the ability to make good measurements (unstable power feed, heat warp, probe binding, etc).

I had that very device right about 2002. Put my whole CD collection on a few mp3 disks. Replaced it a few years later with a 6GB mp3 player.

I’n Windows it is not stored in a keyring but instead in the registry. This has basically the same security threat model as a local key file.

The ssh-agent on Linux will do what you want with effectively the same security. The biggest difference being that it doesn’t run as a system service but instead runs in userspace which can make it easier to dump memory. There are some other agent services out there with additional security options but they don’t change the threat model much.

My memory of the cp command is that attributes such as file times were transferred at the last step. I think this would make rsync safe in most situations where a system crash wasn’t involved.

I think I remember running into that as well but for whatever reason I couldn’t get accelerated-x working with the opengl libraries I was using for school. Likely the issue was just a lack of understanding on my part as I don’t think I had a good grasp of the Linux library loader until well after I graduated.