Been using prusaslicers default PLA profile with issues and this is my first roll of PETG, so I just selected the corresponding profile for that.

It seems so be super stringy whenever there’s movement and when printing the bunny (in vase mode) there’s lots of holes in the model.

I’m not sure if this is an issue with calibration (didn’t do anything when switching from PLA) or if the filament is wet.

  • drudoo@lemmy.worldOP
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    I did two temp towers: 260-225

    And

    280-235 Although my printer didn’t want to go above 260, so the first layers are all 260.

    • blakcod@lemmy.ca
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      Yikes! Are you sure you sliced the temp tower for PETG profile? (as others have inquired)

        • blakcod@lemmy.ca
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          Huge difference!

          Yeah I have Prusament Jet Black and 220/225 is the sweet spot for it on my setup.

          That’s a shame you have to do all of the replacements but looks to solve all sorts of things for you.

      • drudoo@lemmy.worldOP
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        I selected PETG filament profile in prusaslicer.

        I wrote the custom layer change temp code to switch temps and checked in prusaslicer that temp changes occur the right places. (Using the color preview thing)

        While printing I also saw that the temp did change where it should.

        I think I’ll do a calibration of the feeding, or whatever you call it, where you measure how much filament is extruded. During some of the bridging, it looked like nothing got extruded.

        It almost looks like 260 is the best temp. While extruding at this temp, I did heat lots of popping noise, which makes me believe the filament is wet. The noise did not occur at lower temps.

        Kinda annoying when it’s a brand new roll.

        • morbidcactus@lemmy.ca
          link
          fedilink
          English
          arrow-up
          2
          ·
          1 year ago

          What’s your print fan set to? I’ve had better results with fixed fan speed and much higher than default, but I use an enclosure. Is it popping or skipping? You’ll hear clicking if the filament skips, happens if you feed too fast, partial clogs etc. What brand petg? 260 seems high-ish, I tend to print hot in general but petg is usually 245-250 depending on the filament. What’s your speed like? If you’re enclosed definitely crank the print fan and maybe try slowing down.

          Is your hotend clogged? Petg is the only filament I’ve had clogging issues with in the past. While printing, is it trying to cling to the nozzle? I’ve also found petg can try to climb up the nozzle, solved with a sock.

          • drudoo@lemmy.worldOP
            link
            fedilink
            English
            arrow-up
            2
            ·
            1 year ago

            Update: replaced the nozzle, heat block (heating element, sensor, PTFE) and fan duct. Did two new temp towers:

            Left tower is 235 (top) to 260 (layers labeled 280-260 are all 260). Right is 220-240.

            https://i.imgur.com/1MQkStE.jpg

            https://i.imgur.com/HDWq19A.jpg

            I definitely feel like 220 is the right temp for this.

            In regards to the fan, I actually read a post saying PETG wants almost no fan, so I just left it on default but maybe I should try a fixed fan speed.

            I’m pretty sure the popping noise was clogged PLA burning like crazy at 260c…

            • morbidcactus@lemmy.ca
              link
              fedilink
              English
              arrow-up
              1
              ·
              1 year ago

              I’ve always understood petg to really like cooling but I print in an enclosure so YMMV, it’s absolutely awful for bridges without cooling. Another thing to check would be extrusion multiplier and retraction. I get nozzle buildup if it’s overextruding which leads to blobs and stringing, worth tuning that anyhow

              • drudoo@lemmy.worldOP
                link
                fedilink
                English
                arrow-up
                2
                ·
                1 year ago

                Been doing a couple of test prints with 30-80% variable fan speed and it’s actually pretty good looking with almost no stringing.

                I unfortunately don’t have an enclosure, else I would for sure try and higher fan speed. Ad a slight draft this morning and my calibration cube print popped off half way through.